As a supplier of 98% sodium formate, I am often asked about the synthesis process of this high - purity chemical. In this blog post, I will share the scientific and practical methods for synthesizing 98% sodium formate.
Introduction to Sodium Formate
Sodium formate (HCOONa) is a white, crystalline, hygroscopic powder with a wide range of applications. It is used in industries such as leather tanning, textile dyeing, electroplating, and as a reducing agent in chemical reactions. The 98% purity grade is particularly valuable for applications where high - quality raw materials are required.
Common Synthesis Methods
1. Reaction of Sodium Hydroxide with Formic Acid
One of the most common methods for synthesizing sodium formate is the reaction between sodium hydroxide (NaOH) and formic acid (HCOOH). This is an acid - base neutralization reaction, which can be represented by the following chemical equation:
$HCOOH + NaOH \longrightarrow HCOONa+ H_{2}O$
Procedure:
- Materials Preparation: First, prepare the required materials. You need high - purity formic acid and sodium hydroxide. For achieving 98% sodium formate, it is crucial to start with pure reactants. The formic acid should be at least 99% pure, and the sodium hydroxide should be of reagent - grade quality.
- Reaction Setup: Set up a reaction vessel, which is usually a glass or stainless - steel reactor. The reactor should be equipped with a stirrer to ensure uniform mixing of the reactants. A thermometer is also necessary to monitor the reaction temperature.
- Reaction Process: Slowly add sodium hydroxide solution (prepared by dissolving sodium hydroxide in water) to the formic acid solution while stirring continuously. The reaction is exothermic, so it is important to control the addition rate to prevent a sudden increase in temperature. The ideal reaction temperature is around 60 - 70°C.
- Neutralization End - Point Determination: Use a pH meter to monitor the pH of the reaction mixture. The reaction is complete when the pH reaches around 7 - 8, indicating that the acid has been neutralized by the base.
- Evaporation and Crystallization: After the reaction is complete, transfer the reaction mixture to an evaporation dish. Evaporate the water from the solution by heating it under reduced pressure. As the water evaporates, sodium formate crystals will start to form. Cool the solution slowly to allow for the growth of large, pure crystals.
- Purification: The obtained sodium formate crystals may contain some impurities. To achieve 98% purity, recrystallization can be carried out. Dissolve the crystals in a minimum amount of hot water and then cool the solution slowly again. The impurities will remain in the solution, while the pure sodium formate will crystallize out.
2. Reaction of Carbon Monoxide with Sodium Hydroxide
Another method for synthesizing sodium formate is the reaction between carbon monoxide (CO) and sodium hydroxide. The chemical equation for this reaction is:
$CO + NaOH \longrightarrow HCOONa$
Procedure:
- Materials and Equipment: You need carbon monoxide gas, which should be free from impurities such as sulfur compounds and other contaminants. Sodium hydroxide solution is also required. The reaction is usually carried out in a high - pressure reactor made of corrosion - resistant materials such as stainless steel.
- Reaction Conditions: The reaction takes place at high pressure (around 1 - 2 MPa) and elevated temperature (120 - 130°C). The carbon monoxide gas is bubbled through the sodium hydroxide solution in the reactor.
- Reaction Monitoring: During the reaction, monitor the pressure and temperature inside the reactor. The reaction rate can be controlled by adjusting the flow rate of carbon monoxide and the reaction temperature.
- Product Separation: After the reaction is complete, the reaction mixture contains sodium formate and some unreacted sodium hydroxide. Separate the sodium formate from the solution by filtration and evaporation. Similar to the previous method, recrystallization can be used to purify the product to 98% purity.
Quality Control and Assurance
To ensure that the synthesized sodium formate has a purity of 98%, strict quality control measures should be implemented.
- Analysis Methods: Use analytical techniques such as high - performance liquid chromatography (HPLC) or titration methods to determine the purity of the sodium formate. HPLC can accurately measure the content of sodium formate and detect any impurities present in the sample.
- Impurity Detection: Check for common impurities such as sodium carbonate, sodium chloride, and unreacted formic acid or sodium hydroxide. These impurities can affect the quality and performance of the sodium formate in its applications.
Our Company's Offerings
As a supplier of Sodium Formate 98%, we not only provide high - quality sodium formate but also offer other grades of sodium formate, such as Sodium Formate 92% and Sodium Formate 95%. Our products are synthesized using advanced production processes and strict quality control measures to ensure consistent quality.
Contact for Purchase and Negotiation
If you are interested in purchasing sodium formate, whether it is 92%, 95%, or 98% grade, we welcome you to contact us for further negotiation. Our team of experts can provide you with detailed product information, technical support, and competitive pricing. We are committed to meeting your specific requirements and providing you with the best possible service.


References
- "Advanced Inorganic Chemistry" by F. Albert Cotton and Geoffrey Wilkinson.
- "Industrial Chemistry" by Kirk - Othmer.
- Journal articles on the synthesis and applications of sodium formate from "Journal of Chemical Technology and Biotechnology" and "Industrial & Engineering Chemistry Research".
